Pour une installation optimale des postes connectés, veuillez suivre les étapes ci-dessous :

For optimal installation of the connected stations, please follow the steps below :

1. Plug the hub (ref. 80016658) into a 220V power outlet. Ensure it is positioned high and centrally within the building (for multi-level buildings, prioritize the highest level) to allow for optimal site coverage and a good connection to the GSM network.

2. Choose the locations for the stations on the site and create them in the interface at https://aegis.connect.liphatech.fr/

3. Open the station with the AEGIS universal key, place the baits in the designated slots, and attach the fixing cable. For the use of rodent baits, folllow the usage recommendations indicated on the labels of each product.

4. Press and hold the button located under the cover.

5. Wait for a rapid and simultaneous flashing of the ON and OFF lights (video to be added) : this indicates that the station has successfully detected the hub and is connected to it.

6. The lights will then flash 11 times at a frequency of one second. Close the station during these flashes and position it in the desired location.

7. A reference photo is automatically taken at the 11th flash and transmitted to the AEGIS.CONNECT platform. The reference photograph will appear on the site after about thirty minutes. For more details, watch the explanatory video. (add video)

Follow the steps below :

1. Reposition the station if necessary.

2. Press the button under the cover for 1 second.

3. Wait a quick and simultaneous flashing of the ON and OFF lights (video to be added) : this indicates that the station has successfully detected the hub and is connected to it.

4. The lights will then flash 11 times at a frequency of two seconds. Close the station during these flashes. The reference photo is taken after the 11th flash.

Press and hold the single button until the OFF lights remains steady ; the station will turn off once the button is released.

Under the cover at the location of the electronic card.

You can use baits in the form of pastes or blocks

Yes

Before moving a connected ALL IN BOX, turn it off. Position it in the chosen location and turn it back on. 

Remember to make the location change on AEGIS.CONNECT.

If you are using the vertical rods, it is preferable to place the baits on the 3 middle rods so that the photo sensor can analyse consumption most effectively.

If you are using the horizontal rod, place the baits in the middle of it and position it on the middle rail.

The connected ALL IN BOX has an IP rating of 54.

No, as it would damage the photo sensor when it closes.

Yes. You can find this information on AEGIS.CONNECT, where it will show :

·       The number of rat passages

·       The number of mouse passages

You will receive an alert message to notify you of the loss of connection to the hub.

Once power is restored, the ALL IN BOX units automatically reconnect to the hub.

1.       In a navigation panel located on the screen’s left, choose the site for which you want to edit the PDF report

2.        In the « Editing » tab (on top of the screen) click on « Generate PDF »

3.       Click on the « + » next to the site name

4.       Change some elements if necessary

5.       Remember to save (below the page)

1.       Make sure that the following elements have been successfully created on AEGIS.CONNECT :

a-The client

b-The site to be protected

c-The building(s) and optionally their storey(s)

2.       For the connected objects (trap, station or hub), make sure to have their serial number(s) beforehand (SGXXXXXX ou PMXXXXXX or PCXXXXXX depending on the type of object). You could refer to the answer to question n°24.

3.       Position yourself at the chosen building or storey level.

4.       Begin to create the hub : in the Editing tab, select « Object Management ». On top of the screen, choose the number of objects to create and click on « go ». In the drop-down menu, choose « Hub », click on « go » and fill in the required fields.

5.       To create your stations or traps, follow the same steps : select in the drop-down menu the objects to create, as well as their number, click on « go » and fill in the required fields. Remember to provide the number of the hub they will be attached to.

In the case of a single object creation, in the Editing tab, select « Object Management ». On top of the screen, choose the number of objects to create and click on « go ». The map view opens with a creation panel on the right, by default the object type is « connected station », it’s up to you to choose the object you want to create, fill in the required fields, then click on « Validate ».

6.       You can also create non-connected objects : non-connected station, non-connected trap multi-capture, mechanical rat or mouse snap traps.

7.       Click on the « Save » button to finalize the creation of all objects.

To create a new user (manager or technician) from the homepage

1.Go in the « User » tab located on top of the screen.

2.Click on the « New user » tile.

3.Fill in the form specifying the clients or sites to which this new user will have access.

4.Remember to specify the type of email alerts they will receive.

To create a new connected object, you must first create a hub by providing the serial number. Then, you can create new objects (stations or traps) attached to this hub.

You can create as many client as you wish.

·       To move a connected object (station or trap) to another site and to relate it to a new hub, you just need to right-click on the icon of the object to be moved, then click on « More information ». In the window that opens, click on the « Delete » button. 

Caution : Deleting a station will result in the deletion of all data that the station has already stored (photos, passage counts, etc.).

·       When the object (station or trap) is deleted, you can create a new one on another site or for another client.

1.Plug the hub into the power outlet at least 10 minutes before turning on the stations or traps.

2.Turn on the station or the trap by pressing on the single button : the LED indicator flashes quickly.

3.When logging into the AEGIS.CONNECT platform, check that the « connection signal » icons located next to the objects are green.

1. Click on the station icon.
2. Click on the « More information » button.
3. Stay on the « Information » tab and scroll down the page to click on the « Trigger manual capture » button.
4. A new photo will be uploaded by the hub in less than two hours.

·       At startup, the ON and OFF indicators on the connected station flash simultaneoulsy eleven times, every two seconds. This period allows the applicator to position the station properly and close it. A reference photo is then automatically taken after the eleventh flash.

·       A new photo is automatically triggered every 24 hours and compared with the reference photo.

·       If there is a significant difference between the 2 photos, the snapshot (« automatic trigger photo ») is transmitted to the AEGIS.CONNECT platform. It allows to visualize changes that have occurred in bait stations or mousetraps.

In AEGIS.CONNECT, click on the station icon, then on the « More information » button. Choose the « Advanced data » tab. There you will find estimated of passages by species (rat or mouse) based on dates and times.

·       In AEGIS.CONNECT, click on the trap icon, the number of captured and battery status are visible on the right side of the screen.

·       For more detailed information, click on the « More information » button. Choose « Advanced data » tab : you will find the number of captures based on dates and times.

• ·       On top of the AEGIS.CONNECT screen, click on the « Editing » and then on « Building management » tab.  
• ·       In the preview pane, on the left of AEGIS.CONNECT screen, select the relevant screen and click on the « pencil » icon next to the building for which a plan needs to be added.
• ·       Click on the « Choose » button. The picture must be in JPEG or PNG format.
• ·       Click on « Confirm » and then « Save ».
  

·       In the « Users » tab, at the top of the AEGIS.CONNECT screen, select a user and click on « Edit ». You can then activate or deactivate the email alerts received by the user. There are three types of alerts :

1.Trigger alerts (captures at the trap or snapshot triggered at the station)

2.Activity level evolution (information related to the tracking of passage numbers)

3.Technical issues.

This is not possible, as specified in Article 6 of the AEGIS.CONNECT platform subscription agreement.

·       The dashboard provides an overview of all objects (hubs, traps and stations) as well as on the maintenance or trigger alerts.

·       With manager or administrator access, you can assign alerts to a technician or handle these alerts by yourself.

·       With their access, the technician sees alerts related to the sites they are responsible for, as well as alerts assigned to them. They can then handle them.

·       For assigning alerts

·       For ALL IN BOX connected objects : the icon changes colour automatically based on the number of passages recorded by the station.

1-      Green : the station works but there are very few passages.

2-      Orange : between 20 and 40 passages recorded.

3-      Red : more than 40 passages recorded.

·       Trap multi-capture CLASH !: the icon is green between 0 and 5 captures, it is becoming orange from 6 captured mice and red from 16 captured mice.

·       For non-connecting stations, this configuration is done manually by the applicator based on their observations in the field.

·       Regarding the exclamation point, it indicated the upload of a photo triggered automatically by the connected station. This means bait consumption or mousetrap triggering.

In the « Status » column, an exclamation point appears when there is no communication (loss of connection, battery failure, central hub disconnected) with the station.

An exclamation point appears in the trigger column when a photo taken automatically by the connected station is transmitted to AEGIS.CONNECT. This indicated that bait has been consumed, a mousetrap has been triggered, or the passage threshold has been reached.

1.Choose the relevant site.

2.Position yourself on the building or storey to be modificated. Click on the tab at the top right « Edit » then on « Building management ».

3.With the pencil icon you can change the plan by clicking on the « edit image » button. JPEG and PNG formats are compatible with the software.

1.Choose the relevant site and building.

2. In the « Edit » tab, on top of the screen, select « Building management ». Click on the « + » icon then on the « choose an image » button to upload the storey plan. Choose where to insert it above. JPEG na d PNG formats are compatible with the software.

3. You can rename this new level by clicking on the pencil icon.

4.Click « Confirm » and then « Save ».

This entry is only possible if you have an « Administrator » or « Manager » account.

Click on the « Client » tab at the top of the screen, then on « + ». Fill in the required information.

·       For the exterior of the site, search for its address on Google Maps and take a screenshot. Then, embed this image into the paltform.

·       For the interior of the site, ask your client for a sanitation plan, or take a photograph of the premises’ evacuation plan.

·       To be integrated into the AEGIS.CONNECT platform, these images must be in JPEG or PNG format.

You can :

•   Reset the connected station by pressing the multifunction button for 2 seconds.
• Or, from the AEGIS.CONNECT. platform, select the relevant connected station (PC…) and click on the « Reset » button.

You will find serial numbers :

·       On the invoice

·       On the shipping carton

·       Inside the cover of the connected ALL IN BOX station and the trap multi-capture CLASH !.

·       On the label attached behind the hub.

LThe two first letters of the serial number indicate the type of connected object : SG for Surigate (hub) – PC for connected station (ALL IN BOX) – PM for trap multi-capture (CLASH !).

1.Create the connected objects on the AEGIS.CONNECT platform starting with the hub.

2.Place them on the plan you have downloaded, approximately in the area where you intend to position them.

3.Go to the site to be protected to position the connected objects in the appropriate locations. First, plug in the hub and then turn on the connected objects.

4.You can now adjust the position of the connected objects on the AEGIS.CONNECT platform and start tracking.

This may be due to a brief network disconnection. Click on the « Reset » button to upload the reference photo. It may be take a few minutes before it appears on the AEGIS.CONNECT platform.

The station communicates with the hub every 2 hours to exchange various information : number of rodent passages, photo transmission, photo request, etc. If you trigger a manual snapshot, this one will be done and transmitted to the AEGIS.CONNECT platform upon the station / hub communication. The delay between your trigger request and the photo display is therefore a maximum of 2 hours.